EPDM membrane
Wide sheets of EPDM cover the roof with as few seams as possible.
Flat Roofing
Rubber Roof Installation Roselle, NJ
A roofer in Roselle can install a rubber roof by laying EPDM membrane in wide sheets over insulation and a cover board, bonding or fastening it down and sealing every seam with primer and tape, and explain each choice before the sheet is rolled out. Call (908) 620-5317 to reach a local roofer.
A true rubber roof is EPDM, a synthetic rubber membrane used on flat and low slope roofs for decades. EPDM is sold in wide rolls, typically 45 or 60 mil thick, and it stretches and recovers as the roof moves through hot and cold seasons. Unlike TPO and PVC, its seams are taped rather than heat welded.
EPDM can be attached in three main ways. Adhered, fastened and ballasted systems each suit different buildings and wind conditions. For homes, adhered EPDM is the most common choice.
Thickness and color are the next choices. A 60 mil sheet is tougher than 45 mil for roofs that see foot traffic. White EPDM suits sunny roofs, and black suits cooler climates. The transition to a steeper roof or a wall is planned with the same care, since that is where low roofs most often leak.
Depending on what the roofer finds, rubber roof installation in Roselle, NJ can go hand in hand with rubber roof repair and flat roof installation.
Looking for Roselle rubber roof installation? Call (908) 620-5317 to talk to a local roofer.
Call nowThe process
How rubber roof installation works
Each layer is set up to give the membrane a smooth, solid base.
Check the base
The deck is repaired and checked for slope, ideally a quarter inch per foot toward drains or gutters. On a replacement, old layers come off first.
Add the cover board
Rigid insulation, often polyiso, is fastened with plates and screws, then a cover board goes on top. Low spots can be corrected with tapered insulation.
Lay the sheet
Wide sheets are laid out to cover the roof with as few seams as possible, then allowed to relax. Seams are planned so they run with the slope.
Apply adhesive
Half the sheet is folded back, adhesive is applied to both surfaces and the rubber is pressed into place. Each half gets the same treatment in turn. Any trapped air is worked out so the sheet lies flat and does not blister.
Tape the laps
Seam areas are cleaned and primed, then seam tape is applied and rolled firmly with a seam roller. Lap sealant goes along exposed tape edges.
Flash the details
Perimeter edge metal, wall flashing and pipe boots complete the roof. Counter flashing covers the top of wall flashing. Before the crew leaves, seams are probed for any loose spots.
What is included
Parts of a new EPDM roof
Edge metal
Walls, curbs, pipes and edges are flashed for a finished roof.
Insulation
A cover board protects the insulation and gives the adhesive a firm grip.
Seam tape
Every seam gets primer and tape for a lasting bond.
Tear-off
Old roofing is removed and the deck is repaired so the roof sits on solid wood.
Related service
EPDM Roof Installation Roselle, NJ
The quality of an EPDM installation shows up years later in the seams and edges. A flat, dry base, properly timed adhesive and carefully primed seams are what make EPDM last. Weather matters too, since adhesives and primers need dry conditions. Different adhesives may be used in the field and at the flashings, each matched to the job it does.
For a Roselle home, the installer thinks ahead to how the roof will behave over the years. Securing the membrane at the edges and flashing corners correctly prevents later tears. It is worth asking how the edges will be secured.
Local help
Rubber Roof Installation Near Me
In Roselle, EPDM is a popular choice for low slope roofs on additions and attached garages. Homes in Roselle and nearby places including Roselle Park, Linden, Kenilworth and Cranford benefit from rubber roofing because it flexes with the seasons, which is why the seams and flashing deserve careful attention.
For rubber roof installation in Roselle, NJ or nearby towns like Roselle Park, Linden, Kenilworth and Cranford, call (908) 620-5317 to reach a roofer who covers your street.
What the local climate does to a roof
Cold winters bring snow, ice and a long stretch of freezing nights. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. That is why roof repair in Roselle is busiest after a hard winter and before the next one.
Why call
Why fix it now
Drier ceilings
Small roof problems caught early usually stay small repairs.
Familiar with local homes
Local roofers see the same roofs and storm damage across Roselle and nearby towns.
Straight answers
Ask your questions before you agree to anything.
Rubber Roof Installation questions
Is it possible to install EPDM over the old roof?
Recovering depends on the condition of the old roof. The old roof must be a single dry layer, with a recover board over it. If the old roof is wet, it must come off. The roofer tests the old roof for moisture before recommending a recover.
Is a rubber roof the same as TPO?
EPDM is synthetic rubber, while TPO is a thermoplastic membrane. EPDM is usually black, very flexible and seamed with tape, while TPO is usually white, more reflective and heat welded at the seams. Both are common on flat roofs.
What is the lifespan of a new EPDM roof?
Rubber roofs often last decades. Thickness, seam quality and maintenance all affect its life. Patching EPDM is straightforward.
How thick should a rubber roof be?
Most residential EPDM is 45 or 60 mil. The thicker sheet holds up better to traffic and weather. Thicker 90 mil membrane exists for heavy use.
What color EPDM is best?
The choice depends on the climate and the space below. Black holds heat and white reflects it. A roofer can recommend what fits your home.
More questions? Call (908) 620-5317
Often needed together
Rubber Roof Repair
EPDM rubber roof repairs done with primer, cover tape and lap sealant made for rubber, so the membrane seals again without a tear-off.
Learn moreFlat Roof Installation
Flat roof installation from the deck and tapered insulation up to the seams, flashing and edge metal, so water drains instead of ponding.
Learn moreTPO Roofing
Heat-welded TPO membrane for flat and low-slope roofs, with seams welded into one watertight sheet.
Learn moreFlat Roof Replacement
Replacing old built-up, torch-down, EPDM or TPO roofs with a new system built to drain, and new flashing at every wall, curb and drain.
Learn more
Looking for something else?
See all roofing servicesNeed rubber roof installation in Roselle, NJ?
Call (908) 620-5317 for a local roofer in Roselle and nearby towns.